Railing Systems from The Wagner Companies Ultra-Tec® Railing
Systems were created to enhance aesthetics
and flexibility in any setting. All
hardware components come in a variety
of sizes and material choices that
can be configured to meet your specific
System is the only cable railing system to feature
Invisiware®. Invisiware™ hardware is hidden
inside the end posts providing a clean look unmatched
by any other cable connector
Railing frame components can be
specified in a variety of materials: carbon
steel pipe; structural tubing; stainless steel; and
Finishes can include: unfinished;
galvanized; primed and painted; and powder coated.
Type 316 stainless steel cable and
hardware are used. Due
to the increased amounts of nickel and the addition
of molybdemun, type 316 stainless steel has excellent
resistance to atmospheric and general corrosive conditions.
Our exclusive Invisiware® hardware
is hidden inside the end posts, so it is virtually
invisible. We also offer hardware which is visible
when installed but is streamlined with smooth rounded
corners and is more compact than awkward turnbuckles
intended for other uses. All of our hardware has been
designed specifically for pedestrian cable railings
and is arguably the very best available for that use.
All Ultra-tec® Cable Railing
System hardware can be swaged in the field, by using
one of our portable swaging tools. Swaging
in the field allows intermediate posts and braces to
be bored just slightly oversized of the diameter of
the cable being used, as only the cable will have to
pass through. Otherwise, the intermediate posts and
braces have to be bored slightly over the larger diameter
of the swaged fitting which will have to pass through
the intermediate post or brace. (If desired, fittings
can be swaged onto one or both of the cable ends at
the factory.) ? By using our pre-tensioning tool, runs
of up to 150 ft. and longer can be achieved while maintaining
tight cable tension using our hardware.
Our stylish tubed corner sections, which
can be prefabricated at our factory, allow a change in
direction without risk of damage to the cables. At the
same time, they offer the streamlined look of a continuous
piece of cable (which runs through the tube) and eliminate
the cost and visual obstruction of additional mounting
and tensioning hardware. Tubed corner sections can be
provided in many styles and angles, including a simultaneous
change in direction with a change in elevation. We will
gladly assist in the design of tubed corner sections
not illustrated in our standard specifications.
When ordered from the factory, all
posts and other railing components (including vertical
system top and bottom rails) are drilled and counter-bored
where required using CNC milling equipment to insure
product uniformity and accuracy. This is also the least
expensive method of boring posts and rails.
We stock a wide variety of standard styles
and sizes of railing hardware and components, which can
be shipped to your fabricator or to the job site.
Check our vast inventory
of stock components for pipe and tube handrails,
guardrails and railings -- handrail; handrail
brackets, pipe and tube elbows, flanges, end
caps and connectors; slip-on pipe railing fittings;
spheres and hemispheres; disks and plates,
tubing, bars and shapes, and ornamental metal
Aluminum, brass, bronze,
steel and stainless steel brackets for
wall and post mounting of handrails. All
brackets will meet structural code requirements
when properly installed. ADA compliant
brackets are available. More.
and Tube Connectors
Coped drive-on Connectors,
Wedge-Lock® Welding Connectors, Splice-Locks®,
Insert Sleeves and Couplings. Mechanical
and weld connectors for aluminum, steel and
stainless steel tube and pipe. More.
Round disks and square and rectangular
plates in steel, aluminum, brass, or stainless. May be purchased
with our without holes. Special finishes and hole configurations
are available upon request. More.
Balls and Hemispheres
Full range of sizes in
steel, aluminum, stainless and brass, these
hollow balls and hemispheres have found a multitude
of uses in applications as varied as casino
ornamentation to monumental sculpture. More.
Drive-on and Weld-on end
caps for pipe and tube in aluminum, brass,
steel and stainless steel. More. . .
Square and Rectangular Post Caps for aluminum,
brass, bronze, steel and stainless steel tube. Cast and Stamped options
are available. More.
Standard and custom industrial
strength bike racks in steel and stainless
Services Offered Polishing, Bending
and Fabrication. R & B Wagner, Inc., offers
architects and designers dimensional accuracy
in small bends and in large radius bending
configurations. A wide variety of sizes and
shapes can be rotary or roll bent by our experienced
personnel. Metals that are worked include steel,
stainless steel, aluminum, brass and bronze.
Several finishes are available for custom bending.
Galvanized, zinc-plated, anodized, polished
and specialized finishes can be applied to
meet your requirements. More
. . .
Glass Railing featuring the new PanelGrip®
Dry Mount System as well as components for
a wet glaze glass railing. Designed for use
with 1/2" and 3/4" tempered glass panels as
structural balusters. More. .
Railing Ultra-Tec® Cable
Railing System is the only cable rail system
to feature Invisiware®. Invisiware™ hardware
is hidden inside the end posts providing
a clean look unmatched by any other cable
railing connector. More.
Aluminum, brass, bronze, steel and stainless
steel pipe and tube elbows in a complete range of OD sizes, varying
inside radii and angles. Special finishes and sizes are available
upon request. More.
Aluminum, bronze, steel and stainless flanges
in multiple styles, sizes and hole configurations. Most designs
are available with or without set screws. Special finishes
and hole configurations are available upon special request. More.